2017 Ford Raptor Stock Front Bumper Removal

ford-raptor-front-bumper-removal

Congratulations on your purchase of the all-new 2017 Ford Raptor! Like with all Raptor owners, having a stock truck for our off-road adventures just isn’t enough because we keep wanting to push it to the limits. You are probably looking to install and uplift your truck to give it your own personal blend.

One of the easiest ways to modify your new Ford Raptor is to install some awesome looking aftermarket front bumpers. If you are into upgrading your stock Ford Raptor parts you might want to check out some of our earlier blogs that go in depth at some of the hottest looking 2017 Ford Raptor aftermarket parts

Once you’ve found that one Ford Raptor bumper that you just cannot resist you’re going to need to install it. You could take your Raptor into a shop and have it installed, but if you are anything like us you won’t might getting your hands dirty.

We’ve prepared detailed instructions on how to remove your stock Ford Raptor front bumper so you can get to installing those custom aftermarket front bumpers to make your 2017 Ford Raptor stand out.

What you’ll need to prepare

  • Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
  • Please reading through this entire installation instructions document before performing removal.
  • We estimate around 2 hours of installation time needed to perform this task. 2 people is required for best results.
  • You will need the following tools:
    • Ratchet
    • 3/4″ Socket and Wrench
    • 9/16″ Socket
    • E6 External Torx Socket
    • 7mm Socket
    • 11mm Socket
    • 13mm Socket
    • 15mm Socket
    • 21mm Socket
 
 

Step-by-step guide to remove your stock 2017 Ford Raptor front bumper

  1. Use 13mm and 15mm Sockets to remove the skid plate bolts (x6), then remove the skid plate from the truck. (Fig A)
     

    2017-ford-raptor-skid-plate-removal-fig-a

     
     
  2. Remove the metal spacer that the bottom two skid plate bolts go through. Then, remove the two factory U-nuts that the bottom two skid plate bolts threaded into. (Fig B)
     

    2017-ford-raptor-skid-plate-removal-fig-b

     
     
  3. Carefully pull the front plastic piece off the bumper. There are no tools required for this step, it pulls off by hand. (Fig C)
     

    2017-ford-raptor-oem-front-bumper-removal-fig-c

     
     
  4. Remove your Adaptive Cruise Control Module (Fig D)
     

    2017-ford-raptor-stock-bumper-removal-fig-d

     
    • Using an 11mm Socket, remove the three nuts holding the Module on.
    • Using an E6 External Torx Socket, remove the three studs holding the Module on.
    • Remove the Module
     
     
  5. Remove the 7mm Bolt that holds on the bumper side support bar. Repeat this step on the other side. (Fig E)
     

    2017-ford-raptor-front-bumper-removal-fig-e

     
     
  6. Remove the 21mm Nuts that hold on the bumper. There are three per side. Two of the nuts (per side) face the front (they were hidden behind the plastic piece you removed in Removal Step 3. One of the nuts (per side) faces the rear of the vehicle and is accessible from underneath the truck. (Fig F)
     

    2017-ford-raptor-oem-bumper-removal-fig-f

     
     
  7. Remove the bumper from the truck. As you are removing the bumper, be sure to pull the rubber shroud from the plastic clips that attach it to the bumper. (Fig G)
     

    2017-ford-raptor-remove-stock-bumper-fig-g

     
     
  8. Remove the rubber piece that runs along the bottom/front section of headlight bezel. There are 6 plastic clips holding this on. Repeat this step on the other side of the truck. (Fig H)
     

    2017-ford-raptor-oem-bumper-removal-fig-h

     
     
  9. Remove the tow tooks by removing the two 15mm bolts that hold each of them on. (Fig I)
     

    2017-ford-raptor-remove-oem-bumper-fig-i

     
     
  10. Remove each of the Skid Plate Brackets by removing the 15mm bolt that hold each of them on. There is one bolt per side. (Fig J)
     

    2017-ford-raptor-oem-removal-fig-j

     
     
  11. Prepare to install your new 2017 Ford Raptor aftermarket bumper.
 
 
 

Video Instructions

 
 
 
 
Comments Off on 2017 Ford Raptor Stock Front Bumper Removal